Two data sheets for the same ester. One says flash point 160 °C, the other 138 °C. Neither supplier is lying, and neither product changed — one measured in a closed cup, the other in an open cup. The number on the sheet is only half the information; the method is the other half.

Two cups, two answers

In a closed-cup test (Pensky-Martens, ASTM D93) the sample sits in a covered cup and the ignition source is introduced through a shutter. Vapour cannot escape, so the air above the liquid reaches the flammable range sooner and the flash point reads lower. In an open-cup test (Cleveland, ASTM D92) vapour escapes continuously, so you need a higher temperature to build the same concentration.

The gap is not a constant. It runs from a few degrees on volatile solvents to 20–30 °C on viscous esters and oils, because viscosity controls how fast vapour can leave the surface. That is why no conversion table exists, and why "flash point 160 °C" without a method is an incomplete specification.

The number that decides how a drum ships

ThresholdWhat it triggers
Flash point ≤ 60 °C (closed cup)Class 3 flammable liquid for transport — packing group depends on boiling point and flash point
60 °C < flash point ≤ 93 °CGHS category 4 flammable liquid; still a combustible liquid with storage requirements
Flash point > 93 °CNot classified as a flammable liquid under GHS, though the SDS still reports the value

The 60 °C line is the one that changes paperwork, freight class and warehouse segregation. Most cosmetic esters and white oils sit far above it, which is why they move as general cargo — but a single percent of residual solvent can pull a product across the line. An ester washed and stripped properly might flash at 150 °C; the same ester with 1% hexane left in it will not.

Flash point is not a purity specification

Buyers sometimes treat flash point as a quality number, the way they treat assay or colour. It is not. Two batches can flash 15 °C apart and both be perfectly on-spec, because the test is sensitive to the lightest component present, not to the average composition.

That said, an unexpected drop is a signal worth chasing. If a supplier's isopropyl myristate (CAS 110-27-0) has flashed at 150 °C for three years and the new COA says 128 °C, either the method changed or light ends appeared. Ask which; one is paperwork, the other is contamination. The same applies to isopropyl palmitate (CAS 142-91-6) and diisopropyl adipate (CAS 6938-94-9).

Reading SDS section 9 correctly

  • Look for the method next to the value: "flash point >150 °C (closed cup)" is usable; "flash point 150 °C" is not.
  • Do not compare across suppliers unless both used the same method. This is the single most common source of false alarms in incoming inspection.
  • Flash point is not autoignition temperature. A product that will not flash at 150 °C can still ignite on a hot surface at 350 °C; the two numbers answer different questions.
  • Do not confuse it with the fire point, the temperature at which vapour keeps burning. Fire point sits a few degrees above flash point for most liquids.

What to write in the purchase order

"Flash point ≥ 140 °C, ASTM D93 closed cup" is a clause a lab can test and a supplier can defend. "Flash point ≥ 140 °C" invites a number measured by whichever method was convenient. If you are shipping to a market that classifies by flash point, also ask for the initial boiling point on the same SDS — packing group assignment uses both.

We supply isopropyl myristate (CAS 110-27-0), isopropyl palmitate (CAS 142-91-6), isopropyl laurate (CAS 10233-13-3), diisopropyl adipate (CAS 6938-94-9), C12-13 alkyl lactate (CAS 93925-36-1), cetyl lactate (CAS 35274-05-6), caprylic/capric triglyceride (CAS 65381-09-1), white mineral oil 5# cosmetic grade (CAS 8012-95-1) and 22# industrial grade (CAS 8042-47-5). Flash point and method are stated on every SDS; if you need a specific test method for customs or a factory audit, say which one when you enquire.