Gels rarely fail at the bench. They fail three weeks later, when a botanical extract, a salt-based active, or a new water source quietly adds electrolytes to the water phase. None of that shows up on any COA line, yet it can take a viscosity of 50,000 mPa·s down to a pourable liquid. Electrolytes and pH — not polymer choice alone — decide which thickener survives a formula.
The salt ladder: what 0.5% NaCl really does
Lubrizol's published data on 1% Carbopol dispersions neutralized to pH 6 makes the scale concrete: highly crosslinked Carbopol 974P falls from 55,000 to 28,000 mPa·s at just 0.25% NaCl, and to 15,000 mPa·s at 0.5% — a 73% loss. Lightly crosslinked 971P falls from 10,000 to 6,000 mPa·s under the same salt load. Divalent ions (Ca²⁺, Mg²⁺) are harsher still, and that is exactly what many plant extracts and mineral waters carry with them.
| Chemistry | Thickening mechanism | Electrolyte / pH behaviour | Typical use level |
|---|---|---|---|
| Carbomer (crosslinked polyacrylate) | Swollen anionic particles, charge repulsion | Collapses with electrolytes (73% loss at 0.5% NaCl); viscosity peaks at pH 5.5–7 after neutralization | 0.2–1.0% |
| Xanthan Gum (11138-66-2) | Rigid helix, backbone-stabilized | Stable from pH 2 to 12, tolerant of high salt; 1% ≈ 1,200–1,600 mPa·s | 0.1–0.5% |
| Fatty alcohol lamellar gel network | Liquid-crystal network in the oil phase | Electrolyte-insensitive; thickens by structure, not charge | 2–6% (with surfactant) |
| Associative acrylate polymers | Hydrophobe adsorption bridging | Moderately sensitive; performance tracks the surfactant load | 0.3–1.5% |
| Organic thixotropes (oil phase) | Crystal network in oils | No water phase, so no electrolyte issue | 1–3% |
pH is the second switch
A carbomer gel only exists after neutralization: the particles swell roughly a thousandfold as the carboxylates ionize, and the viscosity peaks in the pH 5.5–7 window that Lubrizol recommends. Push the pH back down with an acidic active — a vitamin C serum, an AHA toner — and the charge repulsion that built the gel is switched off. Xanthan gum sits at the other extreme: supplier data shows little viscosity change between pH 2 and 12, and it stays functional in high-salt systems where carbomer is unusable. Potassium Carbonate (584-08-7) is a useful inorganic pH adjuster when triethanolamine would add odour or discoloration — but a carbonate releases CO₂ on contact with acid, so dose it where the pH is meant to sit, not as a buffer.
Four dosing rules that survive production
- Add electrolytes and cationic actives after neutralization, and at the lowest dose that does the job — this is the first item on Lubrizol's own mitigation list.
- Assume plant extracts and spring water carry Ca²⁺/Mg²⁺. If the salt load is fixed, raise the polymer level or switch to a salt-tolerant backbone (xanthan, fatty alcohol networks) instead of hoping.
- Pair chemistries instead of pushing one: a small dose of xanthan under a reduced carbomer level restores suspension yield at a fraction of the salt sensitivity.
- Judge salt damage at production shear, not rest viscosity: electrolyte loss shows up first in yield value and suspension — the things that settle out on the line.
What to lock in the spec
- Ask for electrolyte-tolerance data on the exact grade, not the INCI: the same CAS can hide lightly vs highly crosslinked grades with very different salt behaviour.
- Specify the neutralizer type (NaOH vs triethanolamine vs potassium carbonate) — the viscosity curve and final clarity move with it.
- For oil-phase structurants, electrolyte is irrelevant; select on crystallization habit and melting point instead.
Related reading: the process side of xanthan hydration is in our xanthan gum guide, the three thickening mechanisms in the emulsion thickening guide, and what a single viscosity point cannot tell you in the yield-stress guide.
We supply the chemistry for every rung of the ladder: Xanthan Gum (11138-66-2) for salt-tolerant aqueous viscosity, Potassium Carbonate (584-08-7) for inorganic pH adjustment, Behenyl Methacrylate (16669-27-5), Stearyl Acrylate (4813-57-4) and the ready-to-use Acrylamide/Ammonium Acrylate Copolymer (and) Mineral Oil (and) Laureth-7 for associative thickening, Trihydroxystearin (139-44-6) and Behenyl Behenate (17671-27-1) for anhydrous structure, plus the gel-network bases Cetearyl Alcohol (and) Sodium Lauryl Sulfate, Cetearyl Alcohol C16-18 (67762-27-0), Behenyl Alcohol C22 (661-19-8) and Stearyl Alcohol C18 (112-92-5).